Our Service Plans

Save Time! Save Money!

Avoid costly, untimely breakdowns and emergency repairs, while maximizing equipment efficiency.

In an effort to keep plumbing, heating and electrical systems running smoothly in our community, Dailey Electric Inc. proudly offers yearly service contracts.

Our service contracts include precision tune-up’s and professional cleaning at a low cost. Take a look at what our service plans cover and if interested please contact us to set it up an appointment.


Furnace Service Plan Includes: (Annual)

  • Inspect levels of carbon monoxide
  • Visually inspect heat exchanger
  • Vacuum & clean burners & heat exchanger
  • Inspect & oil motor
  • Inspect flue pipe
  • Inspect controls
  • Inspect safety's
  • Inspect for gas leaks
  • Inspect & adjust burners
  • Inspect & adjust pilot
  • Inspect wiring
  • Inspect & clean blower
  • Inspect temperature rise
  • Inspect & adjust thermostat
  • Inspect complete operation of furnace
  • Change filter

Boiler Service Plan includes: (Annual)

  • Replacement of igniter
  • Inspect gas pressure
  • Clean & vacuum burner tubes
  • Inspect operation of  zone valves
  • Inspect pumps
  • Inspect high and low voltage controls
  • Inspect pressure switch
  • Inspect boiler pressure valve
  • Inspect relief valve operation
  • Inspect vent flue pipe
  • Check carbon monoxide levels

Tankless Water Heater Plan includes: (Annual)

  • Inspect all combustion and vent lines for blockage
  • Inspect exhaust vent pipe
  • Inspect the gas pressure of unit
  • Inspect burner assembly, if needed burner will be cleaned
  • Inspect blower
  • Inspect inlet and outlet thermistor
  • Clean out cold water inlet screen

Central Air Conditioner Service Plan Includes: (Annual)

  • Check thermostat calibration
  • Monitor refrigerant pressure
  • Test AC starting capabilities
  • Test air conditioner safety controls
  • Clean and/or replace standard air filters
  • Measure for correct air flow
  • Tighten electrical connections
  • Measure volts and amps
  • Lubricate all moving parts
  • Clean condensate drain
  • Measure temperature difference between supply air and return air
  • Apply protective coating
  • Monitor cooling cycle
  • Inspect evaporator coil
  • Examine installation quality
  • Examine equipment condition area, and clearances
  • Clean condenser coil

Generator Service Plan includes:

  • Change oil and filter after manufacturer’s recommended break-in procedure
  • Change or clean all filters annually
  • Change lubricating oil
  • Replace spark plugs annually
  • Check air inlets and outlets for debris. Clean as necessary
  • Adjust valve clearance after the first 50 hours of operation 
  • Check and add battery fluid (change battery each third year of agreement)
  • Check and add engine coolant (replace engine coolant each third year of agreement)
  • Spray engine linkages with light oil such as WD-40
  • Check voltage and frequency produced by generator and adjust to proper settings
  • Check operation of transfer switch
  • Operate generator under load for ten minutes and check voltage and frequency
  • Confirm Member’s ability to operate transfer switch and generator correctly, and, if necessary, offer limited instruction on these points
  • Provide report to Member of any condition that may require additional service from Dailey Electric, Inc. or that may fall under the manufacturer’s warranty

Geothermal Service Plan Includes: (Annual)

  • Monitor Unit Amp Draw
  • Monitor Line Voltage
  • Change filters
  • Check Temperatures of Air Coil
  • Check Temperature of water feed in and out
  • Check Temperature of superheater
  • Check temperature of Compressor suction and discharge
  • Monitor and adjust operating pressures
  • Evaluate duct system
  • Evaluate refrigerate lines
  • Monitor refrigerate level
  • Servicing of HVAC equipment

If your Geothermal system has just been installed- we recommend changing filters every 3 months the first year and after the first year, annually.


Web Design | Baton Rouge | Louisiana